• <rp id="t53hp"><object id="t53hp"><input id="t53hp"></input></object></rp>
    <tbody id="t53hp"></tbody>

          <button id="t53hp"><acronym id="t53hp"></acronym></button>

          <em id="t53hp"><acronym id="t53hp"><u id="t53hp"></u></acronym></em>
          <button id="t53hp"><acronym id="t53hp"></acronym></button>
          <button id="t53hp"><acronym id="t53hp"></acronym></button>

          <dd id="t53hp"></dd><button id="t53hp"><object id="t53hp"><input id="t53hp"></input></object></button>

          常見問題About Us

          首頁 >常見問題

          環氧地坪漆施工前地面油污清除方法
          發布時間:2018-03-30 瀏覽:668次

          ?近年來隨著人們對環氧地坪漆的了解,其應用范圍也越來越廣,在進行環氧地坪漆施工時經常會遇到基礎地面存在被油污污染的狀況,這時候就需要對油污進行處理,否則會導致環氧地坪漆涂層出現起皮脫落的問題。下面環氧地坪漆廠家就給大家分享常見的油污清除方法。

          In recent years, with people's understanding of epoxy floor paint, its application scope is becoming wider and wider. During the construction of epoxy floor paint, there is often a situation of oil contamination on the base floor. At this time, it is necessary to deal with the oil contamination, otherwise it will lead to the problem of peeling off of the floor paint coating. The following epoxy floor paint manufacturers to share with you the common methods of oil removal. 

          1、用火焰灼燒,但此方法只針對可燃油類,在除油污時應注意不可過度灼燒,否則會使混凝土基面爆裂。

          1. Burning with flame, but this method only aims at fuel oil. When removing oil stain, we should pay attention to not over-burning, otherwise, the concrete base will burst.

          2、用有機溶劑或者水性清洗劑清洗,清洗后要將清理下來的污物及時清除,否則水分或溶劑揮發油污仍然留在基面上。而在用水性溶劑清洗過的基面一定要等到基面完全干燥后才能施工環氧地坪漆。

          2. Wash with organic solvent or water-borne detergent. After cleaning, the dirt should be removed in time. Otherwise, the water or solvent volatile oil contamination will remain on the base surface. The base surface cleaned with water-borne solvent must wait until the base surface is completely dry before the floor paint can be applied.

          3、對于大面積重油污地面。如汽修廠混凝土地面,這些廠區大多被油污浸蝕多年,并己滲透到混凝土結構內,一般方法難以完全清除,我們一般用噴砂的方法,將油類滲透基面表層打磨去除,直到露出潔凈的未被污染的基面。

          3. For large areas of heavy oil-polluted ground. For example, the concrete floor of automobile repair plant is mostly eroded by oil contamination for many years and has penetrated into the concrete structure. The general method is difficult to remove completely. We usually use sandblasting method to grind and remove the surface of oil penetration base surface until the clean and unpolluted base surface is exposed.


          在線留言
          在線咨詢
          掃二微碼
        1. <rp id="t53hp"><object id="t53hp"><input id="t53hp"></input></object></rp>
          <tbody id="t53hp"></tbody>

                <button id="t53hp"><acronym id="t53hp"></acronym></button>

                <em id="t53hp"><acronym id="t53hp"><u id="t53hp"></u></acronym></em>
                <button id="t53hp"><acronym id="t53hp"></acronym></button>
                <button id="t53hp"><acronym id="t53hp"></acronym></button>

                <dd id="t53hp"></dd><button id="t53hp"><object id="t53hp"><input id="t53hp"></input></object></button>
                日本高清视频色视频免费_草草线在成年在线视频_超清无码a片在线观看不卡_十九禁a片在线观看无码